ispLSI 1032EA (R) In-System Programmable High Density PLD Features Functional Block Diagram * HIGH DENSITY PROGRAMMABLE LOGIC -- 6000 PLD Gates -- 64 I/O Pins, Four Dedicated Inputs -- 192 Registers -- High Speed Global Interconnect -- Wide Input Gating for Fast Counters, State Machines, Address Decoders, etc. -- Small Logic Block Size for Random Logic -- Functionally Compatible with ispLSI 1032E * NEW FEATURES -- 100% IEEE 1149.1 Boundary Scan Testable -- ispJTAGTM In-System Programmable via IEEE 1149.1 (JTAG) Test Access Port -- User Selectable 3.3V or 5V I/O Supports MixedVoltage Systems (VCCIO Pin) -- Open-Drain Output Option D7 D6 D5 D4 D3 D2 D1 D0 A0 C7 A2 C5 D Q Logic Array A3 D Q GLB A4 C3 D Q A5 A6 A7 C4 Global Routing Pool (GRP) B0 B1 B2 B3 B4 B5 B6 B7 C2 C1 Output Routing Pool C6 EW Output Routing Pool D Q A1 N E2CMOS(R) Output Routing Pool C0 CLK Output Routing Pool M A 5V C H D 4 ES A IG 5 F N O S R * HIGH PERFORMANCE TECHNOLOGY -- fmax = 200 MHz Maximum Operating Frequency -- tpd = 4.5 ns Propagation Delay -- TTL Compatible Inputs and Outputs -- Electrically Erasable and Reprogrammable -- Non-Volatile -- 100% Tested at Time of Manufacture -- Unused Product Term Shutdown Saves Power * IN-SYSTEM PROGRAMMABLE -- Increased Manufacturing Yields, Reduced Time-toMarket and Improved Product Quality -- Reprogram Soldered Devices for Faster Prototyping 0139A/1032EA Description The ispLSI 1032EA is a High Density Programmable Logic Device containing 192 Registers, 64 Universal I/O pins, four Dedicated Input pins, four Dedicated Clock Input pins and a Global Routing Pool (GRP). The GRP provides complete interconnectivity between all of these elements. The ispLSI 1032EA features 5V in-system programmability (ISPTM) and in-system diagnostic capabilities via IEEE 1149.1 Test Access Port. The ispLSI 1032EA device offers non-volatile reprogrammability of the logic, as well as the interconnects to provide truly reconfigurable systems. A functional superset of the ispLSI 1032 architecture, the ispLSI 1032EA device adds user selectable 3.3V or 5V I/O and open-drain output options. is p * OFFERS THE EASE OF USE AND FAST SYSTEM SPEED OF PLDs WITH THE DENSITY AND FLEXIBILITY OF FIELD PROGRAMMABLE GATE ARRAYS -- Complete Programmable Device Can Combine Glue Logic and Structured Designs -- Enhanced Pin Locking Capability -- Four Dedicated Clock Input Pins -- Synchronous and Asynchronous Clocks -- Programmable Output Slew Rate Control to Minimize Switching Noise -- Flexible Pin Placement -- Optimized Global Routing Pool Provides Global Interconnectivity U SE The basic unit of logic on the ispLSI 1032EA device is the Generic Logic Block (GLB). The GLBs are labeled A0, A1...D7 (Figure 1). There are a total of 32 GLBs in the ispLSI 1032EA device. Each GLB has 18 inputs, a programmable AND/OR/Exclusive OR array, and four outputs which can be configured to be either combinatorial or registered. Inputs to the GLB come from the GRP and dedicated inputs. All of the GLB outputs are brought back into the GRP so that they can be connected to the inputs of any other GLB on the device. Copyright (c) 2002 Lattice Semiconductor Corp. All brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. LATTICE SEMICONDUCTOR CORP., 5555 Northeast Moore Ct., Hillsboro, Oregon 97124, U.S.A. Tel. (503) 268-8000; 1-800-LATTICE; FAX (503) 268-8556; http://www.latticesemi.com 1032ea_04 1 January 2002 Specifications ispLSI 1032EA Functional Block Diagram IN 7 IN 6 I/O 51 I/O 50 I/O 49 I/O 48 I/O 55 I/O 54 I/O 53 I/O 52 I/O 59 I/O 58 I/O 57 I/O 56 I/O 63 I/O 62 I/O 61 I/O 60 Figure 1. ispLSI 1032EA Functional Block Diagram RESET Input Bus VCCIO Generic Logic Blocks (GLBs) Output Routing Pool (ORP) D7 D6 D5 D4 D3 D2 D1 GOE 1/IN 5 GOE 0/IN 4 D0 I/O 47 I/O 46 I/O 45 I/O 44 C4 Global Routing Pool (GRP) A3 A4 C3 N Output Routing Pool (ORP) I/O 8 I/O 9 I/O 10 I/O 11 C5 A2 pM 5V AC H D 4 ES A IG 5 F N O S R lnput Bus I/O 4 I/O 5 I/O 6 I/O 7 Output Routing Pool (ORP) C6 A1 C2 A5 lnput Bus A0 EW C7 I/O 0 I/O 1 I/O 2 I/O 3 C1 I/O 39 I/O 38 I/O 37 I/O 36 I/O 35 I/O 34 I/O 33 I/O 32 A6 I/O 12 I/O 13 I/O 14 I/O 15 I/O 43 I/O 42 I/O 41 I/O 40 C0 B0 TDI B1 B2 B3 B4 B5 B6 CLK 0 CLK 1 CLK 2 IOCLK 0 IOCLK 1 0139B/1032EA B7 Megablock Output Routing Pool (ORP) TDO Clock Distribution Network Y0 Y1 Y2 Y3 A7 I/O 28 I/O 29 I/O 30 I/O 31 I/O 24 I/O 25 I/O 26 I/O 27 I/O 16 I/O 17 I/O 18 I/O 19 TCK I/O 20 I/O 21 I/O 22 I/O 23 Input Bus TMS Clocks in the ispLSI 1032EA device are selected using the Clock Distribution Network. Four dedicated clock pins (Y0, Y1, Y2 and Y3) are brought into the distribution network, and five clock outputs (CLK 0, CLK 1, CLK 2, IOCLK 0 and IOCLK 1) are provided to route clocks to the GLBs and I/O cells. The Clock Distribution Network can also be driven from a special clock GLB (C0 on the ispLSI 1032EA device). The logic of this GLB allows the user to create an internal clock from a combination of internal signals within the device. Eight GLBs, 16 I/O cells, dedicated inputs (if available) and one ORP are connected together to make a Megablock (Figure 1). The outputs of the eight GLBs are connected to a set of 16 universal I/O cells by the ORP. Each ispLSI 1032EA device contains four Megablocks. In addition to the standard output configuration, the outputs of the ispLSI 1032EA are individually programmable, either as a standard totem-pole output or an open-drain output. The totem-pole output drives the specified Voh and Vol levels, whereas the open-drain output drives only the specified Vol. The Voh level on the open-drain output depends on the external loading and pull-up. This output configuration is controlled by a programmable fuse. The default configuration when the device is in bulk erased state is totem-pole configuration. The open-drain/totem-pole option is selectable through the Lattice software tools. U SE is The device also has 64 I/O cells, each of which is directly connected to an I/O pin. Each I/O cell can be individually programmed to be a combinatorial input, registered input, latched input, output or bi-directional I/O pin with 3-state control. The signal levels are TTL compatible voltages and the output drivers can source 2mA or sink 8mA. Each output can be programmed independently for fast or slow output slew rate to minimize overall output switching noise. By connecting the VCCIO pin to a common 5V or 3.3V power supply, I/O output levels can be matched to 5V or 3.3V-compatible voltages. Programmable Open-Drain Outputs The GRP has, as its inputs, the outputs from all of the GLBs and all of the inputs from the bi-directional I/O cells. All of these signals are made available to the inputs of the GLBs. Delays through the GRP have been equalized to minimize timing skew. 2 Specifications ispLSI 1032EA Boundary Scan Figure 2. Boundary Scan Waveforms and Timing Specifications TMS Tbtsu Tbtch Tbth Tbtcl Tbtcp pM 5V AC H D 4 ES A IG 5 F N O S R N TCK EW TDI Tbtvo TDO Tbtco Valid Data Tbtcpsu Data to be captured Tbtoz Valid Data Tbtcph Data Captured Tbtuov Data to be driven out Tbtuco Valid Data Parameter Valid Data Min Max Units tbtcp TCK [BSCAN test] clock pulse width 100 - ns tbtch TCK [BSCAN test] pulse width high 50 - ns tbtcl U SE is Symbol Tbtuoz TCK [BSCAN test] pulse width low 50 - ns TCK [BSCAN test] setup time 20 - ns TCK [BSCAN test] hold time 25 - ns tbtsu tbth trf TCK [BSCAN test] rise and fall time 50 - mV/ns tbtco TAP controller falling edge of clock to valid output - 25 ns tbtoz TAP controller falling edge of clock to data output disable - 25 ns tbtvo TAP controller falling edge of clock to data output enable - 25 ns tbtcpsu BSCAN test Capture register setup time 40 - ns tbtcph BSCAN test Capture register hold time 25 - ns tbtuco BSCAN test Update reg, falling edge of clock to valid output - 50 ns tbtuoz BSCAN test Update reg, falling edge of clock to output disable - 50 ns tbtuov BSCAN test Update reg, falling edge of clock to output enable - 50 ns 3 Specifications ispLSI 1032EA Absolute Maximum Ratings 1 Supply Voltage Vcc .................................. -0.5 to +7.0V Input Voltage Applied ........................ -2.5 to VCC +1.0V Off-State Output Voltage Applied ..... -2.5 to VCC +1.0V Storage Temperature ................................ -65 to 150C Case Temp. with Power Applied .............. -55 to 125C EW Max. Junction Temp. (TJ) with Power Applied ... 150C N 1. Stresses above those listed under the "Absolute Maximum Ratings" may cause permanent damage to the device. Functional operation of the device at these or at any other conditions above those indicated in the operational sections of this specification is not implied (while programming, follow the programming specifications). pM 5V AC H D 4 ES A IG 5 F N O S R DC Recommended Operating Conditions PARAMETER SYMBOL VCC Supply Voltage MIN. MAX. UNITS 4.75 5.25 V 5V 4.75 5.25 V 3.3V 3.0 3.6 V 0.8 V Vcc+1 V Commercial TA = 0C to + 70C VCCIO Supply Voltage: Output Drivers VIL VIH Input Low Voltage 0 Input High Voltage 2.0 Table 2-0005/1032EA Capacitance (TA=25oC, f=1.0 MHz) SYMBOL PARAMETER Dedicated Input, I/O, Y1, Y2, Y3, Clock Capacitance (Commercial/Industrial) C2 Y0 Clock Capacitance is C1 TYPICAL UNITS TEST CONDITIONS 8 pf VCC = 5.0V, VPIN = 2.0V 10 pf VCC = 5.0V, VPIN = 2.0V U SE Table 2-0006/1032EA Erase/Reprogram Specifications PARAMETER MINIMUM MAXIMUM UNITS 10000 - Cycles Erase/Reprogram Cycles Table 2-0008/1032EA 4 Specifications ispLSI 1032EA Switching Test Conditions Input Pulse Levels Figure 3. Test Load GND to 3.0V Input Rise and Fall Time 10% to 90% 1.5ns Input Timing Reference Levels 1.5V Output Timing Reference Levels + 5V 1.5V Output Load R1 See Figure 3 Device Output Table 2-0003/1032EA 3-state levels are measured 0.5V from steady-state active level. Test Point CL* EW R2 A B C Active High Active Low Active High to Z at VOH -0.5V Active Low to Z at VOL +0.5V R1 R2 CL 470 390 35pF *CL includes Test Fixture and Probe Capacitance. pM 5V AC H D 4 ES A IG 5 F N O S R TEST CONDITION N Output Load Conditions (see Figure 3) 390 35pF 470 390 35pF 390 5pF 470 390 5pF 0213a Table 2-0004/1032EA DC Electrical Characteristics Over Recommended Operating Conditions SYMBOL MIN. TYP.3 -- -- 0.4 V IOH = -2 mA, VCCIO = 3.0V 2.4 -- -- V IOH = -4 mA, VCCIO = 4.75V CONDITION PARAMETER VOL Output Low Voltage VOH Output High Voltage IIL Input or I/O Low Leakage Current IIH Input or I/O High Leakage Current IIL-PU IOS1 ICC2, 4, 5 Operating Power Supply Current IOL = 8 mA MAX. UNITS -- -- V -- -- -10 A (VCCIO - 0.2)V VIN VCCIO -- -- 10 A VCCIO VIN 5.25V -- -- 10 A I/O Active Pull-Up Current 0V VIN VIL -- -- -200 A Output Short Circuit Current VCCIO = 5.0V or 3.3V, VOUT = 0.5V -- -- -240 mA VIL = 0.0V, VIH = 3.0V fTOGGLE = 1 MHz -- 153 -- mA U SE is 2.4 0V VIN VIL (Max.) Table 2-0007/1032EA 1. One output at a time for a maximum duration of one second. VOUT = 0.5V was selected to avoid test problems by tester ground degradation. Characterized but not 100% tested. 2. Measured using eight 16-bit counters. 3. Typical values are at VCC = 5V and TA = 25C. 4. Unused inputs held at 0.0V. 5. Maximum ICC varies widely with specific device configuration and operating frequency. Refer to the Power Consumption section of this data sheet and the Thermal Management section of the Lattice Semiconductor Data Book CD-ROM to estimate maximum ICC. 5 Specifications ispLSI 1032EA External Timing Parameters Over Recommended Operating Conditions 4 DESCRIPTION -170 MIN. MAX. MIN. MAX. UNITS 1 Data Propagation Delay, 4PT Bypass, ORP Bypass -- 4.5 -- 5.0 ns 2 Data Propagation Delay, Worst Case Path -- 6.0 -- 7.0 ns A 3 Clock Frequency with Internal Feedback 3 200 -- 170 -- MHz 143 -- 125 -- MHz 250 -- 222 -- MHz 3.5 -- ns -- 3.5 ns 0.0 -- ns 4.5 -- ns -- 4.5 ns 0.0 -- ns 4 Clock Frequency with External Feedback ( ( 1 twh + twl ) ) -- 5 Clock Frequency, Max. Toggle -- 6 GLB Reg. Setup Time before Clock,4 PT Bypass A 7 GLB Reg. Clock to Output Delay, ORP Bypass -- 8 GLB Reg. Hold Time after Clock, 4 PT Bypass -- 9 GLB Reg. Setup Time before Clock -- -- EW -- 1 tsu2 + tco1 3.0 -- -- 3.5 0.0 -- 3.5 -- 10 GLB Reg. Clock to Output Delay -- 4.0 11 GLB Reg. Hold Time after Clock 0.0 -- A 12 Ext. Reset Pin to Output Delay -- 13 Ext. Reset Pulse Duration B C -- 5.5 3.5 -- 14 Input to Output Enable -- 7.0 15 Input to Output Disable -- 7.0 B 16 Global OE Output Enable -- 4.5 C 17 Global OE Output Disable -- 4.5 -- 18 External Synchronous Clock Pulse Duration, High 2.0 -- 19 External Synchronous Clock Pulse Duration, Low -- 20 -- 21 USE 1032EA-2 00 FOR NEW DESIGNS A A -- 7.0 ns 4.0 -- ns -- 9.0 ns -- 9.0 ns -- 6.5 ns -- 6.5 ns -- 2.25 -- ns 2.0 -- 2.25 -- ns I/O Reg. Setup Time before Ext. Sync Clock (Y2, Y3) 3.0 -- 3.0 -- ns I/O Reg. Hold Time after Ext. Sync. Clock (Y2, Y3) 0.0 -- 0.0 -- ns is Unless noted otherwise, all parameters use a GRP load of four GLBs, 20 PTXOR path, ORP and Y0 clock. Refer to Timing Model in this data sheet for further details. Standard 16-bit counter using GRP feedback. Reference Switching Test Conditions section. U SE 1. 2. 3. 4. -200 1 2 # N tpd1 tpd2 fmax (Int.) fmax (Ext.) fmax (Tog.) tsu1 tco1 th1 tsu2 tco2 th2 tr1 trw1 tptoeen tptoedis tgoeen tgoedis twh twl tsu3 th3 TEST COND. pM 5V AC H D 4 ES A IG 5 F N O S R PARAMETER 6 Table 2-0030A/1032EA v.2.4 Specifications ispLSI 1032EA External Timing Parameters Over Recommended Operating Conditions 4 A 1 Data Propagation Delay, 4PT Bypass, ORP Bypass A 2 A 3 -- 4 Clock Frequency with External Feedback ( tsu2 + tco1) 1 2 DESCRIPTION -100 MIN. MAX. MIN. MAX. -- 7.5 Data Propagation Delay, Worst Case Path -- Clock Frequency with Internal Feedback 3 125 1 ( 1 twh + twl ) 5 Clock Frequency, Max. Toggle -- 6 GLB Reg. Setup Time before Clock,4 PT Bypass A 7 GLB Reg. Clock to Output Delay, ORP Bypass -- 8 GLB Reg. Hold Time after Clock, 4 PT Bypass -- 9 GLB Reg. Setup Time before Clock -- -- A 12 Ext. Reset Pin to Output Delay UNITS -- 10.0 ns 10.0 -- 12.5 ns -- 100 -- MHz 100 -- 77 -- MHz 167 -- 125 -- MHz EW -- 4.5 -- 6.0 -- ns -- 4.5 -- 6.0 ns 0.0 -- 0.0 -- ns 5.5 -- 7.0 -- ns 10 GLB Reg. Clock to Output Delay -- 5.5 -- 7.0 ns 11 GLB Reg. Hold Time after Clock 0.0 -- 0.0 -- ns -- 10.0 -- 13.5 ns -- 13 Ext. Reset Pulse Duration 5.0 -- 6.5 -- ns B 14 Input to Output Enable -- 12.0 -- 15.0 ns C 15 Input to Output Disable -- 12.0 -- 15.0 ns B 16 Global OE Output Enable -- 7.0 -- 9.0 ns C 17 Global OE Output Disable -- 7.0 -- 9.0 ns -- 18 External Synchronous Clock Pulse Duration, High 3.0 -- 4.0 -- ns -- 19 External Synchronous Clock Pulse Duration, Low 3.0 -- 4.0 -- ns -- 20 I/O Reg. Setup Time before Ext. Sync Clock (Y2, Y3) 3.0 -- 3.5 -- ns -- 21 I/O Reg. Hold Time after Ext. Sync. Clock (Y2, Y3) 0.0 -- 0.0 -- ns is Unless noted otherwise, all parameters use a GRP load of four GLBs, 20 PTXOR path, ORP and Y0 clock. Refer to Timing Model in this data sheet for further details. Standard 16-bit counter using GRP feedback. Reference Switching Test Conditions section. U SE 1. 2. 3. 4. # N tpd1 tpd2 fmax (Int.) fmax (Ext.) fmax (Tog.) tsu1 tco1 th1 tsu2 tco2 th2 tr1 trw1 tptoeen tptoedis tgoeen tgoedis twh twl tsu3 th3 -125 TEST COND. pM 5V AC H D 4 ES A IG 5 F N O S R PARAMETER 7 Table 2-0030B/1032EA v.2.4 Specifications ispLSI 1032EA Internal Timing Parameters1 PARAM. # 2 -200 DESCRIPTION -170 MIN. MAX. MIN. MAX. UNITS Inputs -- 0.3 -- 0.3 ns 23 I/O Latch Delay -- 4.0 -- 4.0 ns 24 I/O Register Setup Time before Clock 3.0 -- 3.0 -- ns 25 I/O Register Hold Time after Clock 0.0 -- 0.0 -- ns -- 4.0 -- 4.6 ns -- 4.0 -- 4.6 ns -- 1.1 -- 1.8 ns 26 I/O Register Clock to Out Delay 27 I/O Register Reset to Out Delay 28 Dedicated Input Delay 29 GRP Delay, 1 GLB Load -- 1.3 30 GRP Delay, 4 GLB Loads -- 1.5 31 GRP Delay, 8 GLB Loads -- 1.7 2.1 pM 5V AC H D 4 ES A IG 5 F N O S R tgrp1 tgrp4 tgrp8 tgrp16 tgrp32 -- 1.4 ns -- 1.6 ns -- 1.8 ns -- 2.2 ns -- 3.0 ns -- 2.1 ns -- 2.0 ns -- 2.3 ns -- 2.2 ns -- 2.2 ns -- 1.0 ns 0.3 -- ns -- ns 32 GRP Delay, 16 GLB Loads -- 33 GRP Delay, 32 GLB Loads -- 2.9 34 4 ProductTerm Bypass Path Delay (Combinatorial) -- 1.7 35 4 Product Term Bypass Path Delay (Registered) -- 1.8 36 1 ProductTerm/XOR Path Delay -- 1.9 37 20 Product Term/XOR Path Delay -- 1.9 38 XOR Adjacent Path Delay 3 -- 1.9 39 GLB Register Bypass Delay -- 0.6 40 GLB Register Setup Time before Clock 0.2 -- 41 GLB Register Hold Time after Clock 1.0 -- 2.0 42 GLB Register Clock to Output Delay -- 1.4 -- 1.4 ns 43 GLB Register Reset to Output Delay -- 3.8 -- 4.7 ns 44 GLB Product Term Reset to Register Delay -- 2.5 -- 2.7 ns U SE is GLB t4ptbpc t4ptbpr t1ptxor t20ptxor txoradj tgbp tgsu tgh tgco tgro tptre tptoe tptck tgfb N GRP USE 1032EA-2 00 FOR NEW DESIGNS 22 I/O Register Bypass EW tiobp tiolat tiosu tioh tioco tior tdin 45 GLB Product Term Output Enable to I/O Cell Delay -- 2.1 -- 3.6 ns 1.5 2.5 1.7 2.7 ns 47 GLB Feedback Delay -- 0.0 -- 0.3 ns 48 ORP Delay -- 0.8 -- 1.0 ns -- 0.1 -- 0.1 ns 46 GLB Product Term Clock Delay ORP torp torpbp 49 ORP Bypass Delay 1. Internal Timing Parameters are not tested and are for reference only. 2. Refer to Timing Model in this data sheet for further details. 3. The XOR adjacent path can only be used by hard macros. 8 Table 2-0036A/1032EA v.2.4 Specifications ispLSI 1032EA Internal Timing Parameters1 PARAM. # -200 DESCRIPTION -170 MIN. MAX. MIN. MAX. UNITS 50 Output Buffer Delay -- 0.9 51 Output Buffer Delay, Slew Limited Adder -- 5.0 52 I/O Cell OE to Output Enabled -- 3.1 53 I/O Cell OE to Output Disabled -- 3.1 54 Global OE -- 1.4 0.9 0.9 EW tob tsl toen todis tgoe Clocks 56 Clock Delay, Y1 or Y2 to Global GLB Clock Line 57 Clock Delay, Clock GLB to Global GLB Clock Line 58 Clock Delay, Y2 or Y3 to I/O Cell Global Clock Line 59 Clock Delay, Clock GLB to I/O Cell Global Clock Line Global Reset tgr 60 Global Reset to GLB and I/O Registers U SE is 1. Internal Timing Parameters are not tested and are for reference only. 9 0.9 0.9 0.8 1.8 0.0 0.0 0.8 2.8 -- 0.0 N 55 Clock Delay, Y0 to Global GLB Clock Line (Ref. clk) pM 5V AC H D 4 ES A IG 5 F N O S R tgy0 tgy1/2 tgcp tioy2/3 tiocp USE 1032EA-2 00 FOR NEW DESIGNS Outputs -- 1.1 ns ns -- 5.0 -- 3.5 ns -- 3.5 ns -- 2.9 ns 0.9 0.9 ns 0.9 0.9 ns 0.8 1.8 ns 0.0 0.0 ns 0.8 2.8 ns 0.4 ns -- Table 2-0037A/1032EA v.2.4 Specifications ispLSI 1032EA Internal Timing Parameters1 PARAM. # 2 -125 DESCRIPTION -100 MIN. MAX. MIN. MAX. UNITS Inputs 22 I/O Register Bypass -- 0.3 -- 0.4 ns 23 I/O Latch Delay -- 4.0 -- 4.0 ns 24 I/O Register Setup Time before Clock 3.0 -- 3.4 -- ns 25 I/O Register Hold Time after Clock 0.0 -- 0.0 -- ns -- 4.6 -- 5.0 ns -- 4.6 -- 5.0 ns -- 1.9 -- 2.2 ns -- 1.7 -- 2.1 ns 30 GRP Delay, 4 GLB Loads -- 1.9 -- 2.3 ns 31 GRP Delay, 8 GLB Loads -- 2.1 -- 2.5 ns 26 I/O Register Clock to Out Delay EW tiobp tiolat tiosu tioh tioco tior tdin 27 I/O Register Reset to Out Delay 28 Dedicated Input Delay pM 5V AC H D 4 ES A IG 5 F N O S R 29 GRP Delay, 1 GLB Load 32 GRP Delay, 16 GLB Loads -- 2.5 -- 2.9 ns 33 GRP Delay, 32 GLB Loads -- 3.3 -- 3.7 ns 34 4 Product Term Bypass Path Delay (Combinatorial) -- 3.4 -- 4.9 ns 35 4 Product Term Bypass Path Delay (Registered) -- 3.1 -- 3.8 ns 36 1 Product Term/XOR Path Delay -- 3.6 -- 4.3 ns 37 20 Prod. Term/XOR Path Delay -- 3.6 -- 4.3 ns 38 XOR Adjacent Path Delay 3 -- 3.6 -- 4.3 ns 39 GLB Register Bypass Delay -- 1.2 -- 2.1 ns 40 GLB Register Setup Time before Clock 0.3 -- 1.4 -- ns 41 GLB Register Hold Time after Clock 3.5 -- 4.0 -- ns 42 GLB Register Clock to Output Delay -- 1.4 -- 1.7 ns 43 GLB Register Reset to Output Delay -- 4.9 -- 5.0 ns 44 GLB Product Term Reset to Register Delay -- 3.8 -- 4.5 ns U SE is GLB t4ptbpc t4ptbpr t1ptxor t20ptxor txoradj tgbp tgsu tgh tgco tgro tptre tptoe tptck tgfb N GRP tgrp1 tgrp4 tgrp8 tgrp16 tgrp32 45 GLB Product Term Output Enable to I/O Cell Delay -- 5.7 -- 7.2 ns 2.8 3.9 3.5 4.7 ns 47 GLB Feedback Delay -- 0.3 -- 0.3 ns 48 ORP Delay -- 1.3 -- 1.4 ns 49 ORP Bypass Delay -- 0.2 -- 0.4 ns 46 GLB Product Term Clock Delay ORP torp torpbp 1. Internal Timing Parameters are not tested and are for reference only. 2. Refer to Timing Model in this data sheet for further details. 3. The XOR adjacent path can only be used by hard macros. 10 Table 2-0036B/1032EA v.2.4 Specifications ispLSI 1032EA Internal Timing Parameters1 PARAM. # -125 DESCRIPTION -100 MIN. MAX. MIN. MAX. UNITS Outputs 50 Output Buffer Delay -- 1.7 -- 2.0 ns 51 Output Buffer Delay, Slew Limited Adder -- 5.0 -- 5.0 ns 52 I/O Cell OE to Output Enabled -- 4.0 -- 5.1 ns 53 I/O Cell OE to Output Disabled -- 4.0 -- 5.1 ns 54 Global OE -- 3.0 -- 3.9 ns 1.1 1.1 1.9 1.9 ns 0.9 0.9 1.5 1.5 ns 0.8 1.8 0.8 1.8 ns 58 Clock Delay, Y2 or Y3 to I/O Cell Global Clock Line 0.0 0.0 0.0 0.0 ns 59 Clock Delay, Clock GLB to I/O Cell Global Clock Line 0.8 2.8 0.8 2.8 ns -- 2.1 -- 5.1 ns EW tob tsl toen todis tgoe Clocks 56 Clock Delay, Y1 or Y2 to Global GLB Clock Line 57 Clock Delay, Clock GLB to Global GLB Clock Line Global Reset tgr N 55 Clock Delay, Y0 to Global GLB Clk Line (Ref. Clock) pM 5V AC H D 4 ES A IG 5 F N O S R tgy0 tgy1/2 tgcp tioy2/3 tiocp 60 Global Reset to GLB and I/O Registers U SE is 1. Internal Timing Parameters are not tested and are for reference only. 11 Table 2-0037B/1032EA v.2.4 Specifications ispLSI 1032EA ispLSI 1032EA Timing Model I/O Cell GRP GLB #47 Ded. In I/O Pin (Input) #60 Comb 4 PT Bypass Reg 4 PT Bypass GLB Reg Bypass ORP Bypass #22 #30 #35 #39 #49 Input D Register Q RST #23 - 27 GRP Loading Delay 20 PT XOR Delays GLB Reg Delay ORP Delay #29, 31 - 33 #36 - 38 I/O Reg Bypass GRP4 I/O Cell Feedback #34 #28 ORP D Q #50, 51 #52, 53 #48 RST #60 Y1,2,3 pM 5V AC H D 4 ES A IG 5 F N O S R #56 - 59 Control RE PTs OE #44 - 46 CK #55 Y0 #54 GOE 0,1 Derivations of tsu, th and tco from the Product Term Clock 1 = = = 0.6 = Logic + Reg su - Clock (min) (tiobp + tgrp4 + t20ptxor) + (tgsu) - (tiobp + tgrp4 + tptck(min)) (#22 + #30 + #37) + (#40) - (#22 + #30 + #46) (0.3 + 1.5 + 1.9) + (0.2) - (0.3 + 1.5 + 1.5) th = = = 1.6 = Clock (max) + Reg h - Logic (tiobp + tgrp4 + tptck(max)) + (tgh) - (tiobp + tgrp4 + t20ptxor) (#22 + #30 + #46) + (#41) - (#22 + #30 + #37) (0.3 + 1.5 + 2.5) + (1.0) - (0.3 + 1.5 + 1.9) tco = = = 7.4 = Clock (max) + Reg co + Output (tiobp + tgrp4 + tptck(max)) + (tgco) + (torp + tob) (#22 + #30 + #46) + (#42) + (#48 + #50) (0.3 + 1.5 + 2.5) + (1.4) + (0.8 + 0.9) U SE is tsu Derivations of tsu, th and tco from the Clock GLB 1 tsu EW Clock Distribution #40 - 43 N Reset = = = 0.8 = Logic + Reg (setup) - Clock (min) (tiobp + tgrp4 + t20ptxor) + (tgsu) - (tgy0(min) + tgco + tgcp(min)) (#22 + #30 + #37) + (#40) - (#55 + #42 + #57) (0.3 + 1.5 + 1.9) + (0.2) - (0.9 + 1.4 + 0.8) th = = = 1.4 = Clock (max) + Reg (hold) - Logic (tgy0(max) + tgco + tgcp(max)) + (tgh) - (tiobp + tgrp4 + t20ptxor) (#55 + #42 + #57) + (#41) - (#22 + #30 + #37) (0.9 + 1.4 + 1.8) + (1.0) - (0.3 + 1.5 + 1.9) tco = = = 7.2 = Clock (max) + Reg (clock-to-out) + Output (tgy0(max) + tgco + tgcp(max)) + (tgco) + (torp + tob) (#55 + #42 + #57) + (#42) + (#48 + #50) (0.9 + 1.4 + 1.8) + (1.4) + (0.8 + 0.9) 1. Calculations are based upon timing specifications for the ispLSI 1032EA-200. Table 2-0042a/1024EA v.2.5 12 0491/1032EA I/O Pin (Output) Specifications ispLSI 1032EA Maximum GRP Delay vs GLB Loads 4 ispLSI 1032EA-100 ispLSI 1032EA-170 ispLSI 1032EA-200 3 1 1 4 8 16 32 GLB Load EW 2 N GRP Delay (ns) ispLSI 1032EA-125 Power Consumption pM 5V AC H D 4 ES A IG 5 F N O S R GRP/GLB/1032EA Power consumption in the ispLSI 1032EA device depends on two primary factors: the speed at which the device is operating, and the number of product terms used. Figure 4 shows the relationship between power and operating speed. Figure 4. Typical Device Power Consumption vs fmax 260 ispLSI 1032EA 240 200 180 160 is ICC (mA) 220 U SE 140 120 100 0 50 100 150 fmax (MHz) 200 250 Notes: Configuration of eight 16-bit counters Typical current at 5V, 25C Icc can be estimated for the ispLSI 1032EA using the following equation: Icc = 20mA + (# of PTs * .52) + (# of nets * Max Freq * .003) Where: # of PTs = Number of Product Terms used in design # of nets = Number of Signals used in device Max freq = Highest Clock Frequency to the device (in MHz) The Icc estimate is based on typical conditions (Vcc = 5.0V, room temperature) and an assumption of four GLB loads on average exists. These values are for estimates only. Since the value of Icc is sensitive to operating conditions and the program in the device, the actual Icc should be verified. 0127/1032EA 13 Specifications ispLSI 1032EA Pin Description TQFP PIN NUMBERS NAME GOE 0/IN 41 66 GOE 1/IN 51 87 IN 6, IN 7 89, TDI 16 TMS 37 TDO 39 TCK 60 RESET 15 Y0 11 Y1 65 Y2 62 Y3 61 Dedicated Clock input. This clock input is brought into the clock distribution network, and can optionally be routed to any I/O cell on the device. 13, 38, 63, 88 12, 64 Ground (GND) VCCIO 14 Supply voltage for output drivers, 5V or 3.3V. NC2 1, 26, 51, 76, EW 17, 21, 29, 33, 40, 44, 48, 56, 67, 71, 79, 83, 90, 94, 98, 6, N 19, 23, 31, 35, 42, 46, 54, 58, 69, 73, 81, 85, 92, 96, 4, 8, 20, Input/Output Pins - These are the general purpose I/O pins used by the logic array. 28, 32, 36, 43, 47, 55, 59, 70, 78, 82, 86, 93, 97, 5, 9 I/O 0 - I/O 3 I/O 4 - I/O 7 I/O 8 - I/O 11 I/O 12 - I/O 15 I/O 16 - I/O 19 I/O 20 - I/O 23 I/O 24 - I/O 27 I/O 28 - I/O 31 I/O 32 - I/O 35 I/O 36 - I/O 39 I/O 40 - I/O 43 I/O 44 - I/O 47 I/O 48 - I/O 51 I/O 52 - I/O 55 I/O 56 - I/O 59 I/O 60 - I/O 63 pM 5V AC H D 4 ES A IG 5 F N O S R This is a dual function pin. It can be used either as Global Output Enable for all I/O cells or it can be used as a dedicated input pin. This is a dual function pin. It can be used either as Global Output Enable for all I/O cells or it can be used as a dedicated input pin. Dedicated input pins to the device. 10 Input - Functions as an input pin to load programming data into the device and also used as one of the two control pins for the ispJTAG state machine. Input - Controls the operation of the ISP state machine. Output - Functions as an output pin to read serial shift register data. Input - Functions as a clock pin for the Serial Shift Register. Active Low (0) Reset pin which resets all of the GLB and I/O registers in the device. Dedicated Clock input. This clock input is connected to one of the clock inputs of all of the GLBs on the device. Dedicated Clock input. This clock input is brought into the clock distribution network, and can optionally be routed to any GLB on the device. is Dedicated Clock input. This clock input is brought into the clock distribution network, and can optionally be routed to any GLB and/or any I/O cell on the device. U SE GND VCC 18, 22, 30, 34, 41, 45, 53, 57, 68, 72, 80, 84, 91, 95, 3, 7, DESCRIPTION 2, 27, 52, 77, 24, 49, 74, 99, Vcc 25, No connect. 50, 75, 100 1. Pins have dual function capability which is software selectable. 2. NC pins are not to be connected to any active signals, Vcc or GND. 14 Table 2-0002A/1032EA Specifications ispLSI 1032EA Pin Configurations EW 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 ispLSI 1032EA Top View NC2 NC2 I/O 38 I/O 37 I/O 36 I/O 35 I/O 34 I/O 33 I/O 32 GOE 0/IN 41 Y1 VCC GND Y2 Y3 TCK I/O 31 I/O 30 I/O 29 I/O 28 I/O 27 I/O 26 I/O 25 NC2 NC2 I/O 7 I/O 8 I/O 9 I/O 10 I/O 11 I/O 12 I/O 13 I/O 14 I/O 15 TMS GND TDO I/O 16 I/O 17 I/O 18 I/O 19 I/O 20 I/O 21 I/O 22 I/O 23 I/O 24 2NC 2NC 2NC 2NC U SE is 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 I/O 57 I/O 58 I/O 59 I/O 60 I/O 61 I/O 62 I/O 63 IN 7 Y0 VCC GND VCCIO RESET TDI I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 2NC 2NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 N 2NC pM 5V AC H D 4 ES A IG 5 F N O S R 2NC 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 NC2 NC2 I/O 56 I/O 55 I/O 54 I/O 53 I/O 52 I/O 51 I/O 50 I/O 49 I/O 48 IN 6 GND GOE 1/IN 51 I/O 47 I/O 46 I/O 45 I/O 44 I/O 43 I/O 42 I/O 41 I/O 40 I/O 39 NC2 NC2 ispLSI 1032EA 100-Pin TQFP Pinout Diagram 1. Pins have dual function capability which is software selectable. 2. NC pins are not to be connected to any active signal, VCC or GND. 100-TQFP/1032EA 15 Specifications ispLSI 1032EA Part Number Description ispLSI 1032EA - XXX X XXXX X Device Family Grade Blank = Commercial Package T100 = 100-Pin TQFP Device Number Power L = Low 0212/1032EA N EW Speed 200 = 200 MHz fmax 170 = 170 MHz fmax* 125 = 125 MHz fmax 100 = 100 MHz fmax pM 5V AC H D 4 ES A IG 5 F N O S R *1032EA-200 recommended for new designs. ispLSI 1032EA Ordering Information COMMERCIAL FAMILY fmax (MHz) 200 ispLSI 170 125 100 tpd (ns) ORDERING NUMBER PACKAGE 4.5 ispLSI 1032EA-200LT100 100-Pin TQFP 5.0 ispLSI 1032EA-170LT100* 100-Pin TQFP 7.5 ispLSI 1032EA-125LT100 100-Pin TQFP 10 ispLSI 1032EA-100LT100 100-Pin TQFP U SE is *1032EA-200 recommended for new designs. 16 Table 2-0041A/1032EA